Skip to main content

Protocol Redistribution EIGRP and OSPF route


 Find below the configurations for route redistribution between OSPF and EIGRP LAB.














 


R1 configurations:

configure terminal interface serial 1/1 ip address 4.1.1.2 255.0.0.0 no shut interface serial 1/0 ip address 1.1.1.1 255.0.0.0 no shut interface fastethernet 0/0 ip address 200.100.50.100 255.255.255.0 no shut router ospf 11 network 1.0.0.0 0.255.255.255 area 0 network 4.0.0.0 0.255.255.255 area 0 network 200.100.50.0 0.0.0.255 area 0 network 200.100.200.0 0.0.0.255 area 0 redistribute eigrp 10 subnets exit router eigrp 10 redistribute ospf 11 metric 1 1 1 1 1


R2 configurations:

configure terminal interface serial 1/0 ip address 1.1.1.2 255.0.0.0 no shut interface serial 1/1 ip address 2.1.1.1 255.0.0.0 no shut interface fastethernet 0/0 ip address 200.100.100.100 255.255.255.0 no shut router ospf 11 network 1.0.0.0 0.255.255.255 area 0 network 4.0.0.0 0.255.255.255 area 0 network 200.100.50.0 0.0.0.255 area 0 network 200.100.200.0 0.0.0.255 area 0 redistribute eigrp 10 subnets exit router eigrp 10 network 200.100.100.100 0.0.0.255 network 2.0.0.0 0.255.255.255 network 3.0.0.0 0.255.255.255 network 200.100.150.100 0.0.0.255 redistribute ospf 11 metric 1 1 1 1 1


R3 configurations:

configure terminal interface serial 1/1 ip address 2.1.1.2 255.0.0.0 no shut interface serial 1/0 ip address 3.1.1.1 255.0.0.0 no shut interface fastethernet 0/0 ip address 200.100.150.100 255.255.255.0 no keep alive no shut router eigrp 10 network 200.100.100.100 0.0.0.255 network 2.0.0.0 0.255.255.255 network 3.0.0.0 0.255.255.255 network 200.100.150.100 0.0.0.255 redistribute ospf 11 metric 1 1 1 1 1


R4 configurations:

configure terminal interface serial 1/1 ip address 4.1.1.1 255.0.0.0 no shut interface serial 1/0 ip address 3.1.1.2 255.0.0.0 no shut interface fastethernet 0/0 ip address 200.100.200.150 255.255.255.0 no shut router ospf 11 network 1.0.0.0 0.255.255.255 area 0 network 4.0.0.0 0.255.255.255 area 0 network 200.100.50.0 0.0.0.255 area 0 network 200.100.200.0 0.0.0.255 area 0 redistribute eigrp 10 subnets exit router eigrp 10 network 200.100.100.100 0.0.0.255 network 2.0.0.0 0.255.255.255 network 3.0.0.0 0.255.255.255 network 200.100.150.100 0.0.0.255 redistribute ospf 11 metric 1 1 1 1 1


EIGRP K-values





How to redistribute the different protocols route in each other. #OSPF #EIGRP #LAB #video #tutorial R4 s1/1 and f0/0 are in OSPF 11 area 0 R2 s1/0 in OSPF 11 area 0 s1/1 & F0/0 in EIGRP 10 R3 s1/1, s1/2, and f0/0 in EIGRP 10. for R3 if you see there is no device attached at fast ethernet interface. so how can we keep this interface active and make sure it doesn't need any hello packets? because we already know that there is no device connected but how to tell this to computer/Router/Network? we will later check this during configuration, meanwhile, you can share your answer in the comments. now let's go to configurations and first we will see the description of commands to check then we will start configurations. these are R1 configurations with their description. steps: 1. configure IP on interfaces and use no shutdown or no shut command to enable the interface. 2. create your OSPF process with your own process ID, I am using 11. 3. then advertise the networks in OSPF till line 16. so how do we choose the networks to advertise which belong to OSPF? for those who don't know check the topology and R1 all 3 interfaces R4 2 interfaces R2 1 interface is in OSPF 11 area 0, we have chosen by our self for each router the protocol we can change it as well. but for this lab, we have chosen as it is shown. so the first network if you see 1.0.0.0 is in b/w R1 and R2 on interfaces S1/0 on both sides. and then 4.0.0.0 b/w R1 and R4 on interfaces S1/1 on both sides in OSPF 11 area 0. and then there are 2 more networks on ethernet of R1 and R4 200.100.50.0/24, 200.100.200.0/24 similarly networks for EIGRP are advertised based on the actual connection R1 have 3 directly connected networks and 1 via OSPF we will verify this as well after configuration if we check from topology network 200.100.200.0/24 will be displayed in routing table as connected via OSPF. if you have any confusion do let me know in the comments box. ok, let's start the configurations. if you give the router command with? you can see the options of protocol configuration so here if you check for advertising network I have used the wild card mask instead of subnet mask wild card mask is opposite of the subnet mask. for detail reading and concept building you can search about it on google. here I have one question we have a wildcard mask while networking advertisement and as well in ACL access control list. so please share your answer in the comment box for difference between wildcard of ACL and OSPF?? share the answer in the comments it is showing only 1 route why?? . . . . . because we have not configured other connected interfaces. let's do and then we will come back and check. now check the routing table O means via OSPF and C means directly connected. R1 has 3 directly connected and 1 via OSPF. D means EIGRP. ok, let's check other routers' tables. R2 has 3 OSPF 1 EIGRP and 3 directly connected keep this in mind and we will verify from the topology as well as from the table O 200.100.200.0/24 C 1.0.0.0/8 is directly connected C 2.0.0.0/8 is directly D 3.0.0.0/8 [90/2681856] via 2.1.1.2, O 4.0.0.0/8 [110/128] via 1.1.1.1, O 200.100.50.0/24 [110/65] via 1.1.1.1, C 200.100.100.0/24 is directly connected, now let's redistribute the ospf and EIGRP. when redistributing OSPF in eigrp check the metrics it's asking for so configuration is done let us check if R1 is showing us EIGRP routes or not? before it was not showing because its all connectivity is based on OSPF now after protocol redistribution it must show us EIGRP routes the terms we get O: via OSPF route C: directly connected O E2: OSPF external type 2 means it is originally eigrp route but after we redistributed eigrp into OSPF it is showing as external OSPF type 2. we have OSPF type 1 and type 2 for external routes. by default, it chooses type 2 The difference between OSPF external type 1 and 2 is as below type 2: it does not show the exact distance from source to destination and Type 1: it shows the exact distance from source to destination. what I am saying is let me show you in the routing table. if you check the R1 table for OSPF external type 2, it has taken 20 as the default value we can change the metric type from 2 to 1... by using this command redistribution eigrp 11 subnets metric-type 1 let me show you. now after setting type 1 on all routers our routing table is showing and now the metric is changed from 20 to 84 if we check R3 we got D EX: it shows external EIGRP means OSPF routes that were redistributed in EIGRP. Thanks for watching.




Labels:

Comments

Post a Comment

Popular posts from this blog

Cyber Attack Countermeasures : Module 4

 Cyber Attack Countermeasures :  Module 4 Quiz #cyber #quiz #coursera #exam #module #answers 1 . Question 1 CBC mode cryptography involves which of the following? 1 / 1  point Mediation of overt channels Mediation of covert channels Auditing of overt channels Auditing of covert channels None of the above Correct Correct! CBC mode is specifically designed to close covert communication channels in block encryption algorithms. 2 . Question 2 Which is a true statement? 1 / 1  point Conventional crypto scales perfectly well Conventional crypto scales poorly to large groups Conventional crypto does not need to scale All of the above Correct Correct! The symmetric key based method inherent in conventional cryptography does not scale well to large groups. 3 . Question 3 Public Key Cryptography involves which of the following? 1 / 1  point Publicly known secret keys Publicly known private keys Publicly known public keys All of the above ...
Post a Comment
Read more

Cyber Attack Countermeasures : Module 2 Quiz

Cyber Attack Countermeasures: Module 2 Quiz #cyber #quiz #course #era #answer #module 1 . Question 1 “Identification” in the process of authentication involves which of the following? 1 / 1  point Typing a password Keying in a passphrase Typing in User ID and password Typing in User ID None of the above Correct Correct! The definition of identification involves providing a user’s ID (identification). 2 . Question 2 Which of the following statements is true? 1 / 1  point Identifiers are secret Identifiers are not secret Identifiers are the secret part of authentication All of the above Correct Correct! Identifiers for users are generally not viewed by security experts as being secret. 3 . Question 3 Which of the following is not a good candidate for use as a proof factor in the authentication process? 1 / 1  point Making sure the User ID is correct Typing in a correct password Confirming location, regardless of the country you are in The move...
Post a Comment
Read more

Rectangular Microstrip Patch Antenna

Microstrip is a type of electrical transmission line which can be fabricated using printed circuit board technology, and is used to convey microwave-frequency signals. It consists of a conducting strip separated from a ground plane by a dielectric layer known as the substrate. The most commonly employed microstrip antenna is a rectangular patch which looks like a truncated  microstrip  transmission line. It is approximately of one-half wavelength long. When air is used as the dielectric substrate, the length of the rectangular microstrip antenna is approximately one-half of a free-space  wavelength . As the antenna is loaded with a dielectric as its substrate, the length of the antenna decreases as the relative  dielectric constant  of the substrate increases. The resonant length of the antenna is slightly shorter because of the extended electric "fringing fields" which increase the electrical length of the antenna slightly. An early model of the microst...
Read more